Levelone VOI-7100 User Manual

LevelOne VOI-7000 VoIP Phone VOI-7100 PoE VoIP Phone User Manual Ver. 2.4 - 1008

5 2.2. Front Panel VOI-7000 VOI-7100 Power LAN RJ45 WAN RJ45 Power LAN RJ45 WAN RJ45 (PoE)

6 Memory Card Use the memory card as a name index for speed dialler or extensions.

7 2.3. Connection Diagram Without Broadband Router With Broadband Router Note Public Switched Telephone Network (PSTN), which refer

8 2.4. Installation 1. Connect IP Phone RJ45 WAN port to NAT Router using a Category 5 LAN cable. 2. Connect IP Phone RJ45 LAN port to Notebook PC

9 2.5. Default Setting IP Address : 192.168.1.100 (LAN) Login Name : root Password : root Note WAN port IP address will depend on the device conn

10 3. Web Configuration You may enter the IP address from PC Web browser to configure IP Phone. For example, enter http://192.168.1.100 from Web bro

11 System Information After login, you will see the system information like firmware version, Codec, etc in this page. You may click the button list

12 3.1. Phone Book The Phone Book specifies pre-record phone list and speed dialling function, it allows up to 140 records on the phone book.

13 Input the Position (0~139), Name and URL, then click the “Add Phone” button to enter. Note URL can be either complete strings or numbers only,

14 Speed Dial Setting For Speed Dial function you can add/delete Speed Dial number up to maximum 10 entries in Speed Dial Phone List.

ii Safety FCC WARNING This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interf

15 If you need to add a phone number into the Speed Dial list, you need to enter the position, the name, and the phone number (by URL type). When you

16 3.2. Phone Setting The sub pages are as follows; Call Forward, SNTP, Volume, Melody (Ringer), DND, Auto Answer, Dial Plan, Flash Time, Call Waiti

17 Call Forward You can have your incoming calls forwarded to a specified destination. You can select the forward mode and enter the forward URL. A

18 All Fwd No Specify All Forward number Busy Fwd No Specify Busy Forward number No Answer Fwd No Specify No Answer Forward number No Answer Fwd Ti

19 SNTP You can setup the primary and second SNTP Server IP Address, to get the date/time information. You may also set the Time Zone, and how long n

20 Volume Raise or lower the sound level by using the Volume Control. For example, if it is difficult to hear the other party's voice; raise the

21 Melody You may set ON the ringer and select different ringer type for Melody settings. Note Because the default ringer is ringer 1, it means

22 Block Setting You can setup the Block Setting to keep the phone silence. You may set this feature when you are in a meeting or busy. Always Bloc

23 Auto Answer You may enable the Auto Answer function to answer the incoming call by FXO port. When the ring count exceeds the number set in Auto An

24 Auto Answer Enable this function to answer the incoming calls from PSTN line automatically. It allows user to place call to Internet again. Auto

iii Table of Contents 1. INTRODUCTION... 1 1.1. FEATURES ...

25 Auto Dial Auto dial timer settings can be set in this page. The auto dial timer specifies the elapse time between the dialling digits. Auto d

26 Call Waiting You can enable the call waiting function in this page. It allows answering another coming call by pressing flash key while holding

27 3.3. Network You can check the Network status, and configure the WAN, LAN, DDNS, VLAN, DMZ, Virtual Server and PPTP settings in this section.

28 Network Status You can check and show the current Network settings in this page. Interface 0 shows WAN port status, and Interface 1 shows LAN port

29 Bridge The Bridge setting is used to configure the Ethernet port connects to the ADSL Modem/Router, or Ethernet switch.

30 Bridge When setting to Bridge Mode, the WAN and the LAN ports will be bridged. IP Type There are three selections for Bridge: Fixed IP, DHCP Clie

31

32 DDNS Setting DDNS (Dynamic DNS) A service that lets anyone on the Internet gain access to resources on your local network when the Internet addres

33 You need to have a DDNS account before configuring the DDNS setting. Usually, most of the VoIP applications are working with a SIP Proxy Server. N

34 3.4. SIP Settings You can setup the Service Domain, Port Settings, Codec Settings, RTP Setting, RPort Setting and Other Settings for SIP Proxy

iv Call Waiting ... 26 3.3. NETWORK ...

35 Understanding the SIP SIP, the Session Initiation Protocol, is a signalling protocol for Internet conferencing, telephony, presence, events notifi

36 Service Domain You may register up to three SIP accounts in the IP Phone. You can call your friends via firstly enabled SIP account and receive th

37 Realm (1 ~ 3) Active Enable the SIP account Display Name Enter the name you want to display User Name Enter the User Name given by your ITSP Reg

38 DTMF Setting You can setup the options for DTMF function in this page. The options include RFC2833 (Outband DTMF), Inband DTMF, and Send DTMF SI

39 STUN Setting The STUN function must be enabled to work properly behind NAT when registered in SIP server. You may enter the STUN server IP addres

40 Codec You can setup the Codec priority, RTP packet length, and VAD function in this page. Codecs basically convert analog signals to digital form

41 Codec Priority Adjust Codec priority to meet your requirement, lower number shows higher priority. RTP Packet Length Adjust Codec g711, g729 and

42 G.729 The G.729 and G.729A conjugate structure algebraic code excited linear prediction (CS-ACELP) coding scheme also compresses PCM using advance

43 Codec ID You can setup the Codec ID in this page. You need to follow the ITSP suggestion to setup these items. Note Two VoIP devices with di

44 Other Settings You can setup the Hold by RFC and QoS in this page. To change these settings please follows your ITSP information. The QoS is used

v 5. SIP Settings ... 58 6. NAT Transversal ...

45 3.5. Auto Config Auto Configuration function can be used to download the original configurations stored in the TFTP or FTP server. Auto Config

46 Note Auto Config is idea for ITSP or large network group to deploy VoIP devices easily

47 ICMP Setting The ICMP function is to echo when someone ping this device. This can prevent from hacker attacking the device by not echoing. ICMP N

48 3.7. Save Change You must save the changes you have made, and click the Save button. After clicking the “Save” button, the IP Phone will save the

49 Update Firmware The IP Phone provides two methods, HTTP or TFTP, to update new firmware as the following steps: 1. Select the firmware code t

50 Caution VOI-7000 and VOI-7100 use different firmware format, check it carefully before upgrade Do Not power off during the upgrade processing,

51 Default Setting You can restore the IP Phone to factory default in this page. By clicking the “Restore” button, the IP Phone will restore to defau

52 4. LCD Display and Keypad You can use keypad to configure and to check the status of IP Phone. Make sure that the WAN port is connected to ADSL E

53 4.1. Keypad Descriptions Key Descriptions 1 “1”, “-“, “٫”, “!”, “?” 2 “2”, “a”, “b”, “c”, “A”, “B”, “C” 3 “3”, “d”, “e”, ”f”, “D”, “E”, “F” 4 “4

54 Key Name Descriptions PHONEBOOK To show the phone book list. CID To show Incoming calls history. OUT To show Outgoing calls history. ENTER The “E

1 1. Introduction The VOI-7000 / VOI-7100 IP Phone is an LCD VoIP Phone with SIP Protocols for Voice over IP (VoIP) applications. This user‟s manual

55 4.2. LCD Menu 1. Phone Book 1.Search Search Phone Book 2.Add entry Add new phone number to phone book 3.Speed dial Add speed dial phone n

56 4.Ring Timeout: Set the Ring times to start the Forward function (2 ~ 8 Rings) 2 Do not Disturb 1.Allways: Block all calls 2.By Period: Bl

57 2.Ringer type: Ringer tone selection from 1~4. 7 Auto Dial Auto Dial time selection from 3~9 seconds. 4. Network 1 Gen

58 5. SIP Settings Note To set the SIP setting from keypad, you have to press Menu_7_4 (Administrator → System Authent) input the password first,

59 2 Codec 1 Codec type G.711 uLaw: G.711 uLaw G.711 aLaw: G.711 aLaw G.723: G.723.1 G.729: G.729A G.726-16: G.726 16Kbps

60 6. NAT Transversal 1 STUN setting 1.STUN: STUN Enabled/Disabled 2.STUN server: Server IP Address 7. Administrator 1 Auto Config 1 C

61 5. Application Example You can use PC Web browser to configure IP Phone. For example, enter http://192.168.1.100 from PC web browser. A. ADSL C

62 5.1. PSTN Calling Applications: VOI-7100 is default at the VoIP mode. For PSTN calls, you may just pick up the phone, press 0* key or PSTN fun

63 5.2. SIP-to-SIP Calling Applications: The SIP-to-SIP calling works when both calling and answering parties are registered to SIP server with gi

64 Dialling without # will not dial out until the auto dial timer (default=5 seconds) elapsed.

2 1.1. Features  SIP v1 (RFC2543), v2 (RFC3261) with MD5 authentication (RFC2069 and RFC 2617)  RJ45 x 2 for Ethernet WAN and LAN ports  ITU

65 5.3. SIP-to-PSTN Calling Applications: The SIP-to-PSTN calling works when both calling and answering parties are registered to SIP server with gi

66 5.4. PSTN-to-SIP Calling Applications: The applications can be for ADSL connections as in both Diagrams A and B. Both parties are registered to

67 5.5. 3-Way Conference Calling Applications: The Call Transfer and 3-Way Conference Call applications are for calls among Parties A, B, and C.

68 3-Way Conference Call: 1. Party A calls Party B. 2. While in conversation, Party B may press Hold key to hold the call, and should hear a dial

69 5.6. Direct IP to Direct IP Calling Applications: The applications are for ADSL connection without NAT router as in Diagram A. Both parties are

70 5.7. FreeWorld Dialup (FWD) Applications: This shows how to use FWD as an example for free ITSP provider. The applications are for both partie

71 SIP Settings You have to enter the Display Name, User Name, Registered Name, Registered Password, Domain Server, Proxy Server, Outbound Proxy. Af

72 Codec Setting Callings: 1. Pick up the phone, and the LCD will show FWD phone number <636346>. 2. Press 12345 to call the party with reg

73 6. Specification Model No. VOI-7000 VOI-7100 Connector 1 x WAN 1 x LAN 1 x Headset Plug 1 x WAN 1 x LAN 1 x Headset Plug 1 x RJ11 FXO LCD Size 16

74 Codec G.711: 64k bit/s (PCM) G.723.1: 6.3k / 5.3k bit/s G.726: 16k / 24k / 32k / 40k bit/s (ADPCM) G.729A: 8k bit/s (CS-ACELP) G.729B: adds VAD

3 1.2. Packing Contents Open the shipping cartons of the Switch and carefully unpacks its contents. The carton should contain the following items:

75 7. Trouble Shooting 7.1. Do not hear dial tone? When you pick up the phone and hear a busy tone, it indicates the WAN port is NOT connected. The

76 Example: To change IP PHONE IP address to the same subnet as PC and NAT router 1. Press the menu to enable DHCP Client mode. IP PHONE will reb

4 2. Hardware Description 2.1. LCD Display and Keypads The LCD display and keypads of IP Phone are as the following. LCD Display Menu Key