LevelOne ProCon GSW-2692 User Manual Page 147
- Page / 390
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
VLAN Configuration
3-111
3
Creating VLANs
Use the VLAN Static List to create or remove VLAN groups. To propagate
information about VLAN groups used on this switch to external network devices, you
must specify a VLAN ID for each of these groups.
Command Attributes
• Current – Lists all the current VLAN groups created for this system. Up to 255
VLAN groups can be defined. VLAN 1 is the default untagged VLAN.
• New – Allows you to specify the name and numeric identifier for a new VLAN
group. (The VLAN name is only used for management on this system; it is not
added to the VLAN tag.)
• VLAN ID – ID of configured VLAN (1-4094, no leading zeroes).
• VLAN Name – Name of the VLAN (1 to 32 characters).
• Status (Web) – Enables or disables the specified VLAN.
- Enabled: VLAN is operational.
- Disabled: VLAN is suspended; i.e., does not pass packets.
• State (CLI) – Enables or disables the specified VLAN.
- Active: VLAN is operational.
- Suspend: VLAN is suspended; i.e., does not pass packets.
• Add – Adds a new VLAN group to the current list.
• Remove – Removes a VLAN group from the current list. If any port is assigned to
this group as untagged, it will be reassigned to VLAN group 1 as untagged.
Web – Click VLAN, 802.1Q VLAN, Static List. To create a new VLAN, enter the
VLAN ID and VLAN name, mark the Enable checkbox to activate the VLAN, and
then click Add.
Figure 3-63 Configuring a VLAN Static List
- LevelOne 1
- Contents 14
- Chapter 1: Introduction 19
- Introduction 20
- System Defaults 23
- Connecting to the Switch 27
- Required Connections 28
- Stack Operations 29
- Basic Configuration 30
- Setting Passwords 31
- Setting an IP Address 31
- Initial Configuration 32
- Dynamic Configuration 32
- Community Strings 33
- Saving Configuration Settings 34
- Managing System Files 35
- Using the Web Interface 37
- Home Page 38
- Panel Display 39
- Main Menu 40
- Manual Configuration 49
- Using DHCP/BOOTP 50
- Managing Firmware 51
- Console Port Settings 56
- Telnet Settings 58
- Configuring Event Logging 60
- Remote Log Configuration 62
- Displaying Log Messages 63
- Resetting the System 66
- Setting the System Clock 67
- Setting the Time Zone 68
- User Authentication 71
- Configuring HTTPS 76
- Configuring the Secure Shell 78
- Generating the Host Key Pair 80
- Configuring the SSH Server 82
- Configuring Port Security 83
- Displaying 802.1X Statistics 90
- Access Control Lists 93
- Setting the ACL Name and Type 94
- Configuring a Standard IP ACL 95
- Configuring a MAC ACL 98
- Port Configuration 100
- Configuring the Switch 102
- Creating Trunk Groups 104
- Configuring LACP Parameters 109
- Displaying LACP Port Counters 111
- Configuring Port Mirroring 118
- Configuring Rate Limits 119
- Rate Limit Configuration 120
- Rate Limit Granularity 120
- Showing Port Statistics 121
- Address Table Settings 126
- Displaying the Address Table 127
- Changing the Aging Time 129
- Displaying Global Settings 130
- Configuring Global Settings 133
- Displaying Interface Settings 136
- VLAN Configuration 141
- Displaying Current VLANs 145
- Creating VLANs 147
- Private VLANs 153
- Configuring Private VLANs 155
- Associating VLANs 155
- Layer 2 Queue Settings 159
- Priority 161
- 13. CLI shows Queue ID 161
- Selecting the Queue Mode 163
- Layer 3/4 Priority Settings 164
- Mapping IP Precedence 165
- Mapping DSCP Priority 167
- Mapping IP Port Priority 168
- Mapping CoS Values to ACLs 169
- Multicast 171
- Multicast Filtering 173
- Accessing the CLI 179
- Console Connection 179
- Telnet Connection 179
- Command Line Interface 180
- Entering Commands 181
- Showing Commands 182
- Partial Keyword Lookup 183
- Using Command History 183
- Understanding Command Modes 183
- Exec Commands 184
- Configuration Commands 184
- Command Line Processing 186
- Command Groups 187
- Line Commands 188
- General Commands 197
- System Management Commands 202
- User Access Commands 203
- IP Filter Commands 206
- Web Server Commands 208
- Telnet Server Commands 211
- Secure Shell Commands 212
- Event Logging Commands 221
- SMTP Alert Commands 227
- Time Commands 231
- System Status Commands 235
- Frame Size Commands 242
- Flash/File Commands 243
- Authentication Commands 249
- RADIUS Client 251
- TACACS+ Client 254
- Port Security Commands 257
- 802.1X Port Authentication 259
- Access Control List Commands 267
- IP ACLs 268
- MAC ACLs 275
- ACL Information 280
- SNMP Commands 281
- Interface Commands 286
- Mirror Port Commands 297
- Rate Limit Commands 299
- Link Aggregation Commands 301
- Address Table Commands 311
- Spanning Tree Commands 315
- VLAN Commands 327
- Configuring VLAN Interfaces 329
- Displaying VLAN Information 334
- Priority Commands 346
- Multicast Filtering Commands 359
- IP Interface Commands 368
- Software Features 373
- Management Features 374
- Standards 374
- Management Information Bases 375
- Software Specifications 376
- Appendix B: Troubleshooting 377
- Using System Logs 378
- Glossary 379
- GSW-2692 390
- E072006-R01 390
Related products and manuals for Network switches LevelOne ProCon GSW-2692
(265 pages)© 2020, manymanuals.com. All rights reserved. | 0.242 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals